If you have a 4 cylinder motor, please email us and let us know!
The industry leader in power and control solutions.
The system utilizes automotive grade approved high-power,
high-temp, ultra-reliable components with a maximum 100 amp capacity! The sPOD
SourceSE is a fully programmable digital CAN-Bus controlled system
utilizing state-of-the-art technologies. OEM vehicle specific simple
installation hardware, engineered and 100% manufactured in the United States.
programmable Digital controlled system.
- Eight circuits rated @30amps
@12.5vdc per circuit that are “End-User” friendly terminal block for
- Expandable (Daisy Chained
selectable) to up to 32 circuits with simple plug-n-play features!
- Low voltage cutoff (LVCO) battery
protection circuit has spec voltage cutoff at 11.2 VDC with a two-minute
delay before shutting down the SourceSE. This
is useful when you have accessories turned on while the vehicle is not
running. When the vehicle starts, the accessories can then be used again.
The low voltage battery protection circuit can be turned off with the DIP
- No more worrying about what
rated fuse to install! The system will protect from 1.5 amps to 30 amps
automatically. The SourceSE incorporates a failsafe self-healing
fault protection system. Fuses have been eliminated (for all accessory
outputs) and replaced with current-sensing MOSFETs controlled by a
microprocessor. This is a great feature for low maintenance and
- Two circuits (switches 1 and 2)
have the option to be activated by an ignition switched power source
(great for accessories that you DO NOT WANT to turn on unless the ignition
key is on). These two circuits can be easily changed to this option by a
simple DIP switch setting on the SourceSE and
running a jumper wire to tap into a fuse that is only activated when the
ignition is on. The same two circuits can also be used as High-Beam
activated circuits by tapping into the input side of one of the
headlight’s high-beam circuits. We have taken care of the PWM issue with
the headlight circuits.
- Shield receptacle for the optional
Bluetooth module for a plug-n-play end-user upgrade. This creates a
scalable platform for future optional enhancements.
- One single ATM mini-style fuse
for LVCO protection and reset.
Touchscreen Control Module Features:
The new touchscreen controller is
small but packs a BIG punch! (3-3/4”w X 2-7/8”h X 5/8” thk) The control
module is a 3.5-inch LED backlit TFT LCD screen with a resolution of 320 x 240,
16.7m colors and a viewing angle of 180 degrees housed in a billet aluminum
case with a 1” RAM mount installed on back panel. The connection between the
SourceSE and the touchscreen uses a small 90 degree 3.5mm standard 4
pin audio jack with a RJ-45 Ethernet plug on the SourceSE end.
Standard cable length will be 12 feet.PLEASE NOTE: Touchscreen case includes a 1" RAM mount installed on back panel but does not include a RAM base. Please ADD your RAM mount base option unless you plan to purchase separately.
o Customization: legends (3 lines of text)
Each switch is programmable for:
o Switch Linking
o On Road & Off Road mode of operation o Multiple Source control up to 32 circuits
Voltage feedback (vehicle’s
temperature feedback (shown on screen)
Automatic power off after 10 minutes
of being inactive
One touch screen off function
One second hold on off button shuts
all circuits down
Automatic system shut down when
touchscreen is unplugged
Touchscreen housing is NOT plastic
but rather, an aluminum billet machined clam-shell designed with several options
Two ports for connection; one on top
and one on bottom
Touchscreens can be daisy chained
for remote operations (EG: one panel in cab and one panel in far back of truck)
can easily add up to 3 touchscreens
Selection of up to 4 sPOD SourceSE
to have control of up to 32 circuits. (DIP switch selectable)
indicate if you are running LUX Lighting Systems LED lights. We will
include a resistor that is required in order for the lights to function